Warehouse floor repairs across the North West, Yorkshire, the Midlands and North East Wales, carried out bay by bay so the rest of the floor keeps working. Cracks, expansion joints, spalled bays and failed resin. Most sites need a repair, not a replacement.
Nearly every repair we attend falls into one of six categories. Which one you have determines whether it is a morning of work or a case for resurfacing the bay.
Caused by substrate movement, shrinkage or impact loading. Fine cracks are stitched and filled; structural cracks need the cause identified before anything is applied over them.
Broken arrises and lost sealant that make forklift wheels bang and judder, damaging both the joint and the truck. The most commonly botched repair on an industrial floor.
Broken bay edges, blown patches and holes around drainage and joints. Cut back to sound concrete and rebuilt with structural resin repair compounds.
Coating separating from the substrate, usually from poor preparation, moisture or contamination at the original installation. The failed area comes off before anything goes back on.
Worn and polished areas where forklift turning circles and pallet traffic have abraded the surface away, leaving thin or bare patches in the busiest runs.
Laitance breaking down into fine dust that contaminates stock, fouls machinery and sensors, and raises cleaning costs. Ground back and sealed rather than patched.
Filling an expansion joint with rigid resin or concrete. It looks solved and it holds for a while, but the joint exists so the slabs either side can move independently. Block that movement and the stress transfers into the surrounding concrete, which then cracks somewhere new.
The second repair is always more expensive than the first, because by then there is a joint to fix and fresh cracking to deal with.
Flexible polysulphide sealants that accommodate movement while giving a smooth trafficable surface across the joint. Where the arrises have broken down, the surrounding concrete is rebuilt with structural resin repair compounds before the sealant goes in.
The result stops forklift wheels banging across the gap, which is usually what prompted the call and what was quietly damaging the trucks as well as the floor.
Most floors we are called to do not need replacing. Damage tends to be concentrated in the areas that take the traffic, which is usually a small proportion of the total area, and localised repair costs a fraction of a new installation.
Resurfacing makes sense when the wear is general rather than local, and when the substrate underneath is still sound. Full replacement is for floors where the concrete itself has failed, or where the specification was wrong from the start and repairing it only buys another year.
We will tell you which of the three you are looking at after the survey, including when the answer is that the floor has more life in it than you think. Without maintenance a resin floor can need resurfacing within five to seven years; with it, the same installation runs fifteen to twenty.
Repairs are localised by definition, which makes them the easiest work to programme around production. We take one bay, aisle or joint run at a time and hand it back as it cures, so the rest of the floor stays in use throughout.
Where the area cannot be released during the day, the work goes into evenings, weekends or a shutdown window. Rapid-cure systems can return a repaired bay to traffic the same day, which matters when the damage is somewhere you cannot route around.
What we do need is the area cleared. Repairing around racking and stock is slower and costs more than moving it, and we will say so at survey rather than after the invoice.
Almost always. Repairs are localised, so we take one bay, aisle or joint run at a time and hand it back as it cures. Where an area cannot be released during the day the work goes into evenings, weekends or a shutdown window, and rapid-cure systems can return a repaired bay to traffic the same day.
It depends on how widespread the damage is and whether the concrete underneath is still sound. Damage concentrated in traffic runs is a repair. General wear over a sound substrate is a resurfacing job. Failed concrete, or a system that was specified wrongly to begin with, is a replacement, because repairing it only buys another year.
Usually because it is moving and the repair was rigid. A crack caused by slab movement will reopen through anything inflexible put into it. The cause has to be identified first, and the repair has to either accommodate the movement or address what is causing it.
The joint exists so the slabs either side can move independently. Filling it rigidly blocks that movement and transfers the stress into the surrounding concrete, which then cracks somewhere new. We use flexible polysulphide sealants that take the movement while still giving a smooth trafficable surface.
Yes, and it is a large part of what we do. Delamination almost always traces back to preparation, moisture or contamination at the original installation, so the failed area comes off and the substrate is tested before anything goes back on. Patching over a failure repeats it.
Repairs are priced per job rather than per square metre, because the cost is driven by access, the extent of the damage and how much preparation the area needs. A survey and a fixed written quotation are free. The cost page sets out full installation rates if the answer turns out to be a new floor.
A few photographs and the size of the affected area are usually enough for an initial view. If it needs a survey we will attend, diagnose the cause rather than the symptom, and quote the repair.
Cookies on this site
We use strictly necessary cookies to make this site work. With your permission we would also like to use analytics cookies to see how the site is used so we can improve it. You can change your choice at any time. See our cookie policy.